Posted by: Teaherman () on Sun Mar 9 14:43:00 2003

Jack,
> >
> > According to Phil Cheetham, our founder and one of the country's leading biomechanical engineers, our findings show a direct relationship to the controlled increase in speed efficiently through each segment, ultimately impacting bat speed.
> >
> > If the speed gain from the hips to the upper torso is in the correct range (not too high or low), there is an expectation of speed gain from the uppertoso to the arms and the arms to the bat.
> >
> > For example if I get a speed gain of 200 degrees per second (dps) from my hips to my upper toso, I would expect to get a similar gain, 200 dps from my upper torso to my arms. I would then expect a large gain from my arms to my bat (800 dps or more). But if I release a large amount of energy during either or those first two segments, that energy cannot be transferred to my bat.
> >
> > Example: I gain 300 dps from hips to uppertorso, and gain 300 dps from my uppertorso to arms, I may only gain 450 dps from my arms to my bat, resulting in a lower bat speed. That loss is only 150 dps. But 150 dps is approximately 10% of the athlete's pre-contact bat speed.
> >
> > Equally important to the acceleration of the segments is the deceleration of each segment at the appropriate time. If I cannot decelerate each segment effectively, I will allow that segment to reach a higher speed. In essence, we would call this a power leak.
> >
> > The athlete with this power leak will appear to the naked eye to have a pretty fast and effective swing. But in our findings that athlete could be better if the athlete learned to control their body and the release of energy from one segment to the next at the right time.
> >
> > Your best contact hitters (Tony Gwynn and others) would be efficient decelerators, not accelerators. It is their use of deceleration that allows them to reach high speed gains and make adjustments to the pitch they are thrown.
> >
> > I spoke with Pat Murphy before the Holidays as we were getting ready to analyze some of his players and he said, "I wonder if it's bat speed or stability at contact the is more important to a hitter?" My response, "Stability." To which he replied, "I would agree. Sometimes I see my guys at the plate with one foot in the box and ready to go, while the other foot is getting ready to bail out. I keep telling them to just dig in and stand your ground, focing them to be more stable."
> >
> > Jack, if an athlete has generated a significant amount of bat speed but cannot decelerate effectively, they will not be able to maximize that speed. In essence, they will have sacrificed control for the "appearance" of speed.
> >
> > In our findings, it is not just the raw bat speed but the acceleration/deceleration of the bat and each segment before it, and when the bat reaches maximum speed during the forward swing that are important.
> >
> > Most of the athletes we have tested had a significantly higher bat speed shortly after contact. This was related to the wrist roll, which occurred after the bat reached an initial peak in bat speed at an angle of between 30 and 45 degrees before contact. At this point the force which generated the first peak in speed is no longer acting on the bat to carry it through the hitting zone. (Power was lost through earlier leaks). The athlete must now try to impart more force to the bat to get it moving again. At this point, it can only be done by rolling the wrists, prematurely.
> >
> > Typically, when an athlete reaches bat speed early, it forces a side bend to the trailing side. Remember, athletes stand in such a way that will allow them to remain in a good athletic position throughout their swing. This athletic position can only be maintained if the maximum amount of speed to the bat is released at the point (or just after) the bat makes contact with the ball. So if you see an athlete with excessive lean early or late in their swing, that is probably the point where the bat reaches a large peak in speed and as a result was at its heaviest weight.
> >
> > There are many devices out there, which I am sure you are aware of that allow an athlete or coach to measure bat speed at a given point (typically in MPH). But nothing that allows you to measure the acceleration and deceleration of the bat and body (in degrees per second), except our technology. That is why I am trying to get the message out there to you and to others that we need to take a much closer look at what happens with the body and the segmental speed gains on the way to the bat.
> >
> > Thank you for your question. I hope this answer is sufficient for you and others.
> >
> > Zig Ziegler
>
> Hi
>
> What is a "biomechanical engineer?" What does that have to do with athletics?
>
> I am sure "biomechanical engineers" have compiled reams of information about various topics. Of what use is it?
>
> Also, are "biomechanical engineers" aware of the way in which elite athletes develop? Are they aware that elite athletes figure out with their unique brand of intelligence that techniques are informed and developed from an understanding of what is required to be successful? Do "biomechanical engineers" understand that great athletes work in a directly opposite fashion from observing and analyzing their peers? That they watch the game, absorb its requirements, and devise techniques aimed at satisfying those requirements?
>
> Of what use is the analysis of "biomechanical engineers," other than journaling - the recording of observations?
>
> Which "biomechanical engineer" has ever used his "biomechanical engineering" background in his professional or high level amateur sports career? Which "biomechanical engineer" has ever done anyting remotely of use to athletes or coaches?
>
> I suspect the answer is "none."
>
> Melvin
>
> Melvin

Please post about which you know.